Electrify your screening operation

Find A Dealer Request More Info
Like the TR626 trommel screen, the TR626EM trommel screen takes the Vermeer trommel screen lineup to the next level with similar design and the ability to tackle tough jobs. The Vermeer TR626EM is equipped with a 150-hp (112-kW) Siemens motor which can help reduce jobsite noise and overall machine maintenance.

Electrify your screening operation

Like the TR626 trommel screen, the TR626EM trommel screen takes the Vermeer trommel screen lineup to the next level with similar design and the ability to tackle tough jobs. The Vermeer TR626EM is equipped with a 150-hp (112-kW) Siemens motor which can help reduce jobsite noise and overall machine maintenance. Find A Dealer Request More Info

Features & Benefits

High production

The tensioned screens around the drum add rigidity, allowing use of small gauge wire, which helps increase production capacity and enable processing of wetter material.

Motor starter panel

The motor starter panel provides a variable frequency drive (VFD) panel.

Electric motors

Powered by two industrial-duty, fully enclosed and fan-cooled electric motors. A single 150-hp (112-kW) motor powers the hydraulic pump stack while a .75-hp (.6-kW) motor powers the cooling fan for the hydraulic system.

Ease of maintenance

The TR626EM was built with the operator in mind, designed with various access points to critical areas helping to make maintenance efficient.

Advance controls

Operators can control the machine through either the Vermeer DP10 display mounted on the control panel, or through a handheld transceiver remote.

Radial stacking conveyor

The stacking conveyor with a 180-degree arc increases the amount of material being stacked on the ground. Adjustable stacking height aids with dust control and helps avoid material being blown away.

Specifications

Compare Models
  • General Dimensions and Weights

    • Weight 49700 lbs 22543.5 kg
    • Hitch Weight 16680 lbs 7565.9 kg
    • Transport Length 54.5 ft 16.6 m
    • Transport Width 113 in 287 cm
    • Transport Height 13.4 ft 4.1 m
    • Operation Length 84.4 ft 25.7 m
    • Operation Width 113 in 287 cm
    • Operation Height 15.9 ft 4.8 m
    • Capacity Approximately 200 cu yd (152.9 cu m) per hour with 0.5 in (1.3 cm) screens installed and material with moisture less than 40%
  • Motor Option One

    • Make and Model Siemens
    • Motor rating 150 hp, 1800 rpm, 460 V, 3 phase
    • System Voltage 12 V, 120 amp alternator
  • Hydraulic System

    • Operation 62.9 gmp @ 2800 psi (238.1 L/min @ 172.4 bar [17240 kPa])
    • Tank capacity 200 gal 757.1 L
  • Chassis

    • Frame Description 4 independent hydraulic jacklegs
    • Axle/Suspension Leaf spring
    • Capacity 22500 lbs 10205.8 kg
    • Tires - Option One 235-75R 17.5H qty. 4
  • Hopper and Apron Conveyor

    • Hopper Capacity 6 cu yd 4.6 cu m
    • Hopper Bottom Width 48 in 121.9 cm
    • Apron Conveyor Speed 0-205 fpm (0-62.5 m/min)
    • Apron Opening Height 34 in 86.4 cm
    • Apron Opening Width 43 in 109.2 cm
    • Hopper Height 9.5 ft (2.9 m) from ground level at operating incline
    • Hopper Opening 13.2 ft x 5.3 ft (4 m x 1.6 m)
    • Apron Conveyor Length 16 ft 4.9 m
    • Apron Conveyor Belt Width 48 in 121.9 cm
    • Apron Conveyor Rollers 4 in (10.2 cm) diameter qty. 14
  • Screen Drum

    • Drum Operation 0-42.6 gpm (161.3 L/min)
    • Drum Motor 48.8 cu in (800 cu cm) displacement
    • Drum Diameter 6 ft 1.8 m
    • Drum Support Description Four steel trunnion rollers 8 in (20.3 cm) diameter, 4 in (10.2 cm) width
    • Drum Length 26 ft 7.9 m
    • Thrust Bearing Diameter 5 in 12.7 cm
    • Thrust Bearing Face 2.9 in 7.4 cm
    • Drum Speed 0-21.6 rpm
    • Drum Drive Chain 140 WT
    • Drum Angle Adjustability 3-5 deg
    • Maximum Screen Panels 8
  • Screen Brushes

    • Brush Diameter 14 in 35.6 cm
    • Bristle Material Polyethylene
    • Brush Assembly Support Two 1.25-in (3.2-cm) sealed ball bearings
  • Collecting Conveyor

    • Conveyor Motor Displacement 32.7 cu-in 535.9 cu-cm
    • Fines Belt Speed 405 ft/min 123.4 m/min
    • Conveyor Belt Width 36 in 91.4 cm
    • Conveyor Belt Type 220 lb (99.8 kg), 2-ply, 2/16 in x 1/16 in (4.8 mm x 1.6 mm)
    • Head/Tail Pulley Type Rubber-lagged, 12 in (30.5 cm ) diameter, 38 in (99.65 cm) wide
    • Head Pulley Bearing 2.4 in (6.1 cm) pillow block
    • Rubber Flashing Adjustable, 0.25 in (6.44 cm) thick, 4 in (10.2 cm)
    • Idler Type 20 degrees CEMA "B" with permanently sealed bearings spaced at 24 in (20.96 cm) centers
    • Tail Pulley Takeup 12 in 30.5 cm
    • Self-Cleaning Return Idlers 6, each 4 in (10.2 cm) diameter
    • Fines Conveyor Frame Part of trailer frame
  • Fines Conveyor

    • Conveyor Operation 15.4 gpm 58.3 L/min
    • Conveyor Motor Displacement 32.7 cu-in 535.9 cu-cm
    • Fines Conveyor Length 72.5 ft 22.1 m
    • Fines Belt Speed 405 ft/min 123.4 m/min
    • Conveyor Belt Width 36 in 91.4 cm
    • Conveyor Belt Type 220 lb (99.8 kg), 2-ply, 2/16 in x 1/16 in (4.8 mm x 1.6 mm)
    • Conveyor Belt Stacking Height 16.6 ft (5.1 m) with drum at 4 deg
    • Head Pulley Type Rubber lagged, 12 in (30.5 cm) diameter, 38 in (99.65 cm) wide
    • Head Pulley Bearing 2.4 in (6.1 cm) pillow block
    • Rubber Flashing Adjustable, 0.25 in (0.64 cm) thick, 4 in (10.16 cm)
    • Troughing Idler Type 20 degrees CEMA "B" with permanently sealed bearings spaced at 24 in (60.96 cm) centers
    • Self-Cleaning Tail Pulley Dimensions 10 in (25.4 cm) diameter, 38 in (96.5 cm) wide with 2.4 in (6.1 cm) shaft
    • Tail Pulley Takeup 12 in 30.5 cm
    • Self-Cleaning Return Idlers 11, each 4 in (10.2 cm) diameter
    • Fines Conveyor Frame 4 in x 8 in (10.2 cm x 20.3 cm) structural steel tubing
  • Fines Conveyor Option-Radial

    • Conveyor Motor Displacement 15.9 cu-in 260.6 cu-cm
    • Fines Conveyor Length 30.5 ft 9.3 m
    • Fines Belt Speed 705 ft/min 214.9 m/min
    • Conveyor Belt Type 150 lb (99.8 kg), 2-ply, 1/32 in x 1/32 in (0.8 mm x 0.8 mm), vulcanized
    • Head/Tail Pulley Type Rubber lagged, crowned, 9.75 in (24.8 cm) diameter, 32 in (81.3 cm) wide
    • Head Pulley Bearing 1.94 in (4.9 cm) pillow block
    • Rubber Flashing Adjustable, 0.25 in (6.4 mm) thick, 4 in (10.2 cm)
    • Idler Type 30 degrees CEMA "B" with permanently sealed bearings spaced at 41 in (104 cm) centers
    • Self-Cleaning Return Idlers 4, each 4 in (10.2 cm) diameter
    • Fines Conveyor Frame 2 in x 8 in (5.1 cm x 20.3 cm) structural steel building
  • Overs Conveyor - Option 1

    • Overs Conveyor Length 20 ft 6.1 m
    • Maximum Variable Overs Belt Speed 290 ft/min 88.4 m/min
    • Conveyor Belt Size 48 in (121.9 cm) wide with raised cleat
    • Conveyor Belt Type 220 lb (99.8 kg), 2-ply, 2/16 in x 1/16 in (4.8 mm x 1.6 mm)
    • Conveyor Belt Stacking Height 3 ft (0.9 m) x 10 ft (3.1 m)
    • Head Pulley Type Rubber lagged, 12 in (30.5 cm) diameter, 51 in (99.65 cm) wide
    • Head Pulley Bearing 2.4 in (6.1 cm) pillow block
    • Self-Cleaning Tail Pulley Dimensions 10 in (25.4 cm) diameter, 51 in (129.5 cm) wide with 2.4 in (6.1 cm) shaft
    • Tail Pulley Takeup 12 in 30.5 cm
    • Solid Return Idler Size 4-in diameter
    • Overs Conveyor Frame 4 in x 8 in (10.2 cm x 20.3 cm) structural steel tubing
  • Overs Conveyor - Option 2

    • Overs Conveyor Length 28 ft 8.5 m
    • Maximum Variable Overs Belt Speed 290 ft/min 88.4 m/min
    • Conveyor Belt Size 48 in (121.9 cm) wide with raised cleat
    • Conveyor Belt Type 220 lb (99.8 kg), 2-ply, 2/16 in x 1/16 in (4.8 mm x 1.6 mm)
    • Conveyor Belt Stacking Height 3 ft (0.9 m) x 12.5 ft (3.8 m)
    • Head Pulley Type Rubber lagged, 12 in (30.5 cm) diameter, 51 in (99.65 cm) wide
    • Head Pulley Bearing 2.4 in (6.1 cm) pillow block
    • Self-Cleaning Tail Pulley Dimensions 10 in (25.4 cm) diameter, 51 in (129.5 cm) wide with 2.4 in (6.1 cm) shaft
    • Head Pulley Takeup 10 in 25.4 cm
    • Rubber disc return idler size 4 in diameter
    • Rattler roller return idler size 5.4 in diameter
    • Overs Conveyor Frame 2 in x 8 in (5.1 cm x 20.3 cm) structural steel tubing

See it in action

Talk to a Vermeer Dealer Today

From helping you select the right equipment, to training operators, to providing the parts and service you need on a jobsite or in the field, Vermeer dealers will give you the localized support you're looking for.

* Required field
*
*
*
*
*
*
*
*
*
I have read and agree to this notice of personal information processing. *
I am 18 years or older. *
I confirm I have read and agree to the Vermeer Privacy Policy, terms and conditions. *
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

More from your machine

Government solutions

Government solutions

Use Sourcewell to satisfy and simplify your bidding process.

Learn how
More separation, less waste

More separation, less waste

Breathe easy and get the most out of your material with a Vermeer trommel screen operating on your jobsite.

See special offer
Purchase with Confidence

Purchase with Confidence

Vermeer Confidence Plus asset protection program provides the ongoing service you need to assist in protecting the productivity and value of your equipment.

Learn more

Vermeer Corporation reserves the right to make changes in engineering, design, and specifications; add improvements; or discontinue manufacturing at any time without notice or obligation. Equipment shown is for illustrative purposes only and may display optional or global-region specific features, accessories or components. Please contact your local Vermeer dealer for more information on machine specifications. Vermeer, the Vermeer logo, Equipped to Do More and Navigator are trademarks of Vermeer Manufacturing Company in the U.S. and/or other countries Copyright © 2020 Vermeer Corporation. All Rights Reserved.