The SC382 was made for the tough stumps on your jobsite.

Find A Dealer Request More Info

This SC382 Vermeer stump cutter is equipped with a 37 hp (26.1 kW) EFI Briggs and Stratton Vanguard engine. The optimized cutting wheel on the SC382 gives this machine aggressive cutting capabilities. Along with standard four-wheel drive and the optional front blade, this model is the full package for stump cutting from start to finish.

The SC382 was made for the tough stumps on your jobsite.

This SC382 Vermeer stump cutter is equipped with a 37 hp (26.1 kW) EFI Briggs and Stratton Vanguard engine. The optimized cutting wheel on the SC382 gives this machine aggressive cutting capabilities. Along with standard four-wheel drive and the optional front blade, this model is the full package for stump cutting from start to finish.

Find A Dealer Request More Info

Features & Benefits

Standard four-wheel drive

The SC382 stump cutter is equipped with standard four-wheel drive to offer traction and maneuverability in difficult transport conditions.

Operator presence system

The operator presence system is intended to enhance operator safety by automatically stopping the cutter wheel when the operator releases the hydraulic cutter wheel controls.

Optional hydraulic front blade

The optional hydraulic front blade helps to reduce the amount of manual work during jobsite clean-up.

37 hp (26.1 kW) EFI Briggs and Stratton Vanguard engine

The SC382 stump cutter has a 37 hp (26.1 kW) EFI Briggs and Stratton Vanguard engine.

Specifications

Compare Models
Show Metric
  • General Dimensions and Weights

    • Length 118 in 299.7 cm
    • Width 50.1 in 127.3 cm
    • Height 53 in 134.6 cm
    • Overall Width Transport (without duals) 35.5 in 90.2 cm
    • Weight - Engine Option One 1950 lbs 884.5 kg
    • Weight With Chip Blade Option (Additional) 85 lbs 38.6 kg
  • Engine - Option one

    • Make and Model Briggs & Stratton Vanguard EFI
    • Number of Cylinders 2
    • Gross Horsepower (Maximum) 37 hp 27.6 kw
    • Torque (Max) 49 ft-lb 66.4 Nm
    • Fuel Tank Capacity 10 gal 37.9 L
    • Max Fuel Consumption 3.2 gph 12.1 lph
    • Fuel Type Gas
    • Air Cleaner Dry-type safety element and restriction indicator
    • Oil Filter Spin-on
    • Recommended Oil 10W30 (See engine manual)
    • Oil Volume with Filter 2.5 qt 2.4 L
    • Maximum Angle of Continuous Operation 25 deg
    • Cooling Medium Air
    • Alternator 20/50 amp (rpm-based)
    • Clutch Type Electric clutch with brake
  • Cutterwheel System

    • Cutterwheel Diameter without Teeth 17 in 43.2 cm
    • Cutterwheel Thickness .5 in 1.3 cm
    • Cutterwheel Speed 1560 rpm
    • Cutterwheel Straight Line Dimension 47 in 119.4 cm
    • Cutterwheel Cut Above Ground 24 in 61 cm
    • Cutterwheel Cut Below Ground 15 in 38.1 cm
    • Tooth Description Yellow Jacket cutter system
    • Number of Teeth 20
    • Number of Indexes 2
    • Number of Pockets 20
    • Reversible Pockets/Teeth 20
    • Cutterwheel Guard Standard
    • Chip Containment 7.5 cu ft .2 cu m
  • Cutterwheel Drive Components

    • Belt Type V-belt
    • Number of Primary Belts 2 individual (matched pair)
    • Jackshaft Dimension 1.3
    • Jackshaft Bearing Type Sealed ball
    • Bearing Dimensions 1.3 bore
    • Number of Secondary Belts 6 banded
    • Cutterwheel Shaft 1.8" (4.8 cm)
    • Bearing Dimensions - Secondary Belt 1.8" (4.8 cm) double spherical roller pillow block
  • Hydraulic System

    • Tank capacity 6.5 gal 24.6 L
    • Recommended Oil Type Vermeer HyPower 68
    • System Type Open-loop series system
    • Filtration Method 10 micron fill strainer and 6 micron return filter
    • Pump Flow at Maximum RPM 6.4 gpm 24.2 L/min
    • System relief pressure 2470 psi 170.3 bar
    • Flow Control SmartSweep
    • Directional Control Electric over hydraulic
  • Electrical System

    • System Voltage 12 V
    • Battery 400 CCA
    • Warning Lights Oil pressure, engine fault, operator presence status, clutch engage/disengage status
    • Switches Two-speed 2x4 and 4x4 ground drive, cutter wheel engage/disengage, creep, blade (if applicable)
    • Controller Danfoss
    • Shutdown System Engine low oil pressure
  • Chassis

    • Frame Description Welded tube and plate steel
    • Control Station Description Fixed side location
    • Toolbox Description Standard
    • Steerable Axle Type Hydraulic steering, oscillating axle
    • Degree of Oscillation 12 deg
    • Tires - Option One 5.7"x 8" (14.5 x 20.3 cm) dual standard
    • Fender Description Yes
    • Axle/Suspension Rigid/fixed (rear)
    • Brake Type Spring-applied, hydraulic release at rear motors
  • Ground Drive

    • Low Speed Travel 65 ft/min 19.8 m/min
    • High Speed Travel 130 ft/min 39.6 m/min
  • Option One

    • Chip Blade Dimension Optional - 33" (83.8 cm) wide, 12" (30.5 cm) tall
    • Blade Travel Above Ground 8 in 20.3 cm
    • Blade Travel Below Ground 2.5 in 6.4 cm

See it in action

Video 1
Image 1
Video 2
Image 2
Video 3
Image 3

Talk to a Vermeer Dealer Today

From helping you select the right equipment, to training operators, to providing the parts and service you need on a jobsite or in the field, Vermeer dealers will give you the localized support you're looking for.

* Required field
*
*
*
*
*
*
*
*
*
I have read and agree to this notice of personal information processing. *
I am 18 years or older. *
I confirm I have read and agree to the Vermeer Privacy Policy and conditions of use. *
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

Unmatched partnerships

Stump cutter teeth

Stump cutter teeth

Built tough to withstand the daily grind.

Learn more
MyVermeer

MyVermeer

Get to know your equipment even when you're on the go.

Register now

Vermeer Corporation reserves the right to make changes in engineering, design and specifications; add improvements; or discontinue manufacturing at any time without notice or obligation. Equipment shown is for illustrative purposes only and may display optional accessories or components specific to their global region. Please contact your local Vermeer dealer for more information on machine specifications. Vermeer, the Vermeer logo and Equipped to Do More are trademarks of Vermeer Manufacturing Company in the U.S. and/or other countries. Copyright © 2019 Vermeer Corporation. All Rights Reserved.