D750x900 NAVIGATOR® Horizontal Directional Drill

Engineered for reliability, the field-tested D750x900 is equipped with optimized features for large-diameter drilling. Its penetrating twin Caterpillar C-18 engines produce a maximum of 92,000 ft-lb/125,120 Nm of rotational torque and 750,000 lbs/3,336 kN of thrust/pullback.

Need skilled HDD operators?  Get your employees trained by an industry leader. Learn more.

Features and benefits

  • Operates efficiently with high-torque, low speed Hagglund hydraulic motors that power the rotary and carriage drives so you can run full torque and full rotary rpm simultaneously.
  • Reduces stress on motor because the thrust box bearing-pack assembly is designed to absorb the axial load caused by thrust and pullback.
  • Helps prevent rod wrap or wind-up because its floating vice allows the breakout system to clamp the full rod upsets during breakout of the lower and upper joints.
  • Muscles through difficult ground formations with higher torque than other models.
  • See your Vermeer dealer for comprehensive service and genuine Vermeer replacement parts.
Vermeer Corporation reserves the right to make changes in engineering, design, and specifications; add improvements; or discontinue manufacturing at any time without notice or obligation. Equipment shown is for illustrative purposes only and may display optional or global-region specific features, accessories or components. Please contact your local Vermeer dealer for more information on machine specifications. Vermeer, the Vermeer logo, Equipped to Do More and Navigator are trademarks of Vermeer Manufacturing Company in the U.S. and/or other countries © 2017 Vermeer Corporation. All Rights Reserved.
Length (Minimum Transport) 50.5 ft 15.4 m
Width 8.5 ft 2.6 m
Height (Minimum Transport) 11.5 ft 3.5 m
Weight 101000 lbs 45812.8 kg
Suspension Triple axle with air ride suspension
Front Base Anchor Length 20 ft 6.1 m
Front Base Anchor Width 6 ft 1.8 m
Front Base Anchor Height 24 in 61 cm
Front Flat Anchor Length 9.5 ft 2.9 m
Front Flat Anchor Width 5 ft 1.5 m
Front Flat Anchor Height 8 in 20.3 cm
Rear Base Anchor Length 16 ft 4.9 m
Rear Base Anchor Width 7.8 ft 2.4 m
Rear Base Anchor Height 8 in 20.3 cm
Number of Rear Legs 2
Drill Rack Angle 8 degrees to 12 degrees
Length 10 ft 3.1 m
Width 8.5 ft 2.6 m
Height 9 ft 2.7 m
Weight 6000 lbs 2721.6 kg
Heat and Air Conditioning In-wall combination unit
Length 22.4 ft 6.8 m
Width 8 ft 2.4 m
Height 10.3 ft 3.1 m
Weight 38000 lbs 17236.5 kg
Make and Model (1) CAT C-27
Fuel Type Diesel
Fuel Capacity 500 gal 1892.7 L
Hydraulic Tank Capacity 720 gal 2725.5 L
Maximum Engine RPM 2000 rpm
Gross Horsepower 800 hp 596.6 kw
EPA Certification Family Tier 2 (EU Stage II)
Length 32.2 ft 9.8 m
Width 8 ft 2.4 m
Height 10.3 ft 3.1 m
Weight 57260 lbs 25972.7 kg
Make and Model (2) CAT C-18
Fuel Type Diesel
Fuel Capacity 1000 gal 3785.4 L
Hydraulic Tank Capacity 720 gal 2725.5 L
Maximum Engine RPM 2000 rpm
Gross Horsepower 1200 hp 894.8 kw
EPA Certification Family Tier 3 (EU Stage II)
Length 32.2 ft 9.8 m
Width 8 ft 2.4 m
Height 10.3 ft 3.1 m
Weight 57260 lbs 25972.7 kg
Make and Model (2) CAT C-27
Fuel Type Diesel
Fuel Capacity 1000 gal 3785.4 L
Hydraulic Tank Capacity 720 gal 2725.5 L
Maximum Engine RPM 2000 rpm
Gross Horsepower 1600 hp 1193.1 kw
EPA Certification Family Tier 2 (EU Stage II)
Thrust 768000 lbs 3416.2 kN
Pullback 768000 lbs 3416.2 kN
Maximum Spindle Torque 99400 ft-lb 134768.5 Nm
Maximum Spindle Torque (Low at Maximum Engine RPM) 99400 ft-lb 134768.5 Nm
Maximum Spindle Speed at Maximum Engine RPM (with PS800) 36 rpm
Maximum Spindle Speed at Maximum Engine RPM (with PS1200/PS1600) 54 rpm
Maximum Carriage Speed at Maximum Engine RPM 95 ft/min 29 m/min
Number of Rotation Motors 1
Number of Drive Motors 4
Mud Swivel 3 in 7.6 cm
Breakout Force 253000 ft-lb 343022.5 Nm
Configuration 3-jaw clamp, 8" (20.3 cm)
Weight 3800 lbs 1723.7 kg
Travel 6 ft 1.8 m
Inside Diameter 9.8 in 24.9 cm
Clamp Force 250000 ft-lb 338955 Nm
Configuration 2-jaw clamp
Inside Diameter 10 in 25.4 cm
Remote Lockout Yes
Strike Alert Yes
Vermeer Corporation reserves the right to make changes in engineering, design, and specifications; add improvements; or discontinue manufacturing at any time without notice or obligation. Equipment shown is for illustrative purposes only and may display optional or global-region specific features, accessories or components. Please contact your local Vermeer dealer for more information on machine specifications. Vermeer, the Vermeer logo, Equipped to Do More and Navigator are trademarks of Vermeer Manufacturing Company in the U.S. and/or other countries © 2017 Vermeer Corporation. All Rights Reserved.

Videos

Safe Operation of Directional Boring Tracking Equipment

For all directional drilling tracking equipment.

Images

D750x900 NAVIGATOR® Horizontal Directional Drill

This site uses cookies to ensure you get the best experience on our website. By continuing to use this site, you consent to the usage of cookies.